UNS S35500 Bolting Products
UNS S35500 is listed in the PRECIPITATION-HARDENING STAINLESS STEEL (CUSTOM PRECIPITATION-HARDENING STAINLESS FAMILY) material family. The reference data below should be checked against the governing product specification, product form and delivery condition before selection or certification.
The reference chemistry table for UNS S35500 lists Chromium (Cr): Chromium-based stainless composition; exact range is grade dependent; Nickel (Ni): Used to balance the stainless matrix and precipitation response; Copper / Niobium / Stainless steel (Cu/Nb/Al): Grade-dependent strengthening additions; Carbon (C): Low controlled carbon. Confirm exact limits and analysis tolerances against the governing standard and product form.
The mechanical-property table for UNS S35500 lists Tensile Strength: Approx. 900–1600 MPa; Yield Strength: Approx. 700–1400 MPa; Elongation: Approx. 5–20 %; Hardness: Approx. 250–500 HB HB. These are reference entries; supplied condition, dimensions, test method and governing specification control the requirements, and the figures are not design allowables.
No one-to-one Werkstoff number was verified for UNS S35500 in the cross-reference sources checked for this update. Confirm any proposed EN alternative against the governing specification.
View Technical Information →Standard identification and material designation information for UNS S35500.
The reference chemistry table lists Chromium (Cr): Chromium-based stainless composition; exact range is grade dependent; Nickel (Ni): Used to balance the stainless matrix and precipitation response; Copper / Niobium / Stainless steel (Cu/Nb/Al): Grade-dependent strengthening additions; Carbon (C): Low controlled carbon. Confirm the governing standard, product analysis tolerances and product form before ordering.
| Element | Symbol | Composition |
|---|---|---|
| Chromium | Cr | Chromium-based stainless composition; exact range is grade dependent |
| Nickel | Ni | Used to balance the stainless matrix and precipitation response |
| Copper / Niobium / Stainless steel | Cu/Nb/Al | Grade-dependent strengthening additions |
| Carbon | C | Low controlled carbon |
| Iron | Fe | Balance |
| Other Elements | — | Controlled according to the applicable grade and product specification |
The table reports Tensile Strength: Approx. 900–1600 MPa; Yield Strength: Approx. 700–1400 MPa; Elongation: Approx. 5–20 %; Hardness: Approx. 250–500 HB HB as reference data for UNS S35500. Actual requirements depend on condition, dimensions, test method and specification; these values are not design allowables.
| Property | Value | Unit |
|---|---|---|
| Tensile Strength | Approx. 900–1600 | MPa |
| Yield Strength | Approx. 700–1400 | MPa |
| Elongation | Approx. 5–20 | % |
| Hardness | Approx. 250–500 HB | HB |
UNS S35500 combines the characteristics of its stainless-steel family with grade-specific alloying and heat-treatment behavior suited to its intended service.
Strength is developed through solution treatment followed by controlled aging.
Aged conditions can provide much higher strength than annealed austenitic stainless steel.
Provides useful stainless corrosion resistance, with grade-specific differences.
Mechanical properties depend strongly on the selected aging condition.
UNS S35500 is selected for engineered components and bolting where the material characteristics of this grade match the service environment.
UNS S35500 is considered for high-strength bolting when its grade-specific corrosion, strength and temperature characteristics meet the service requirement.
UNS S35500 is considered for aerospace hardware when its grade-specific corrosion, strength and temperature characteristics meet the service requirement.
UNS S35500 is considered for pump and valve components when its grade-specific corrosion, strength and temperature characteristics meet the service requirement.
UNS S35500 is considered for precision mechanical components when its grade-specific corrosion, strength and temperature characteristics meet the service requirement.
Always specify the exact UNS grade and aging condition.
Use condition-specific mechanical and fatigue data for design.
Check galling, hydrogen exposure and corrosion compatibility for threaded applications.
No one-to-one Werkstoff number was verified for UNS S35500 in the cross-reference sources checked for this update, so this page does not assign a number. Confirm any proposed EN alternative against the applicable product standard and supplier certificate before substitution.
Our engineering team can help you select suitable materials based on operating temperature, pressure and service conditions.